Anti-Passback in Access Control Systems

Anti-Passback in Access Control Systems

The anti-passback (APB) feature is designed to prevent misuse of the access control system. The anti-passback feature establishes a specific sequence in which access cards must be used in order for the system to grant access.

The anti-passback (APB) feature is most commonly used at parking gates, where there is both an “in” reader at the entry gate and an “out” reader at the exit gate. The anti-passback feature requires that for every use of a card at the “in” reader, there be a corresponding use at the “out” reader before the card can be used at the “in” reader again. For the typical user of the parking lot, this works fine, because the user would normally swipe their card at the “in” reader to get into the lot in the morning, and swipe it at the “out” reader to get out of the lot in the evening. So long as the sequence is “in – out – in – out – in – out”, everything works fine. However, if a user swipes his card at the “in” reader to get in, and then passes his card back to a friend, the card would not work the second time when it was swiped by the friend. The attempt to use the card a second time would create an “in – in” sequence that is a violation of the anti-passback rules, and this is why access would be denied.

Picture Left: (1.) First the cardholder enters into the area and then the system will allow them to (*2.) exit.

Picture Right: If a cardholder has already (1.) entered and then before they exit they try (or someone else with their card tries) to enter again, the will be (3.) denied because there is an anti-passback violation because it is impossible to Enter and area when the system thinks you are already Inside.

Anti-passback can also be used at employee entrance doors. This requires that a card reader be installed on both the inside and the outside of the door. Employees are required to both "card-in" when they enter the building and "card-out" when they leave the building. The anti-passback feature is also commonly used with turnstiles.

There is an expanded version of the anti-passback feature called “regional anti-passback”. This establishes an additional set of rules for card readers inside of the building itself. Basically, this rule says that unless a card is first used at an “in” reader at the building exterior, it cannot be used at any reader within the interior of the building. The theory is that, if a person did not enter through an approved building entrance, he or she should not be permitted to use any of the readers within the building.

Depending on the access control system manufacturer, there may be additional anti-passback features in the system. Some of these features could include "timed anti-passback", which requires that a designated amount time pass before an access card can be used at the same reader again, and "nested anti-passback" which requires that readers be used in only designated sequence to enter or leave a highly-secured area.

Denying access when a user attempts to use a card out of sequence is sometimes called "hard" anti-passback. Hard anti-passback means that when a violation of the anti-passback rules occurs, the user will be denied access. Some access control systems also offer a feature known as "soft" anti-passback. When a system is using this option, users who violate anti-passback rules are permitted access, but the incident is reported to the person managing the access control system so that corrective action can be taken - most often notifying the offending employee that the access card should be used in the proper sequence in the future.

The anti-passback feature can also be integrated with the corporate computer system, preventing users from logging on to the network at their desktop computer unless they have properly entered the building using their access card. This feature can also temporarily disable the users remote log-on privileges while the user is in the building - the theory being that if the user is at work, there is no reason for someone from off-site to be logging on to the network using his or her user name and password. When the user leaves the building at the end of the day, his or her remote log-on privileges are turned back on.

Some Typical Situations

A. When someone enters the entry gate following others without his own authentication, he or she cannot get through the exit gate through his own authentication even his authentication is a valid one. It’s the same when someone gets through the entry gatefollowing others without his own authentication, he or she cannot get through the entry gate through his own authentication.

B. When someone gets through the gate, and then he or she “passes back” that card, say through a window or another door, to an unauthorized user, who then uses the same card to access the building, he or she cannot get through. The password authentication is the same.

C. When someone get through the Fingerprint/Card/Password authentication, he or she doesn't access, then he or she cannot get through the gate even the authentication is a valid one.

Set up an Anti-passback SYRiS Controller Exp:-

Set up an Anti-passback Suprema BioStar V1.62 Software Exp:-

Anti-passbackis a security mechanism that prevents a person from passing back her access card to the next person. It is designed to prevent the next person from verifying herself with another person's access card. When using BioStar, you can set up an Anti-pass back zone, which requires users who've already entered an area to leave the zone first before entering the area again. For instance, if the zone consists of two devices (let's call them Device A and Device B here), the user who's been already verified on Device A must verify herself on Device B before verifying herself on Device A again.

You can set up an anti-passback zone by performing the following steps:

1. On the Doors page, click Add New Zone.

2. Enter a name for the Anti-passback zone and choose Anti-passback Zone from the Type drop-down list.

3. Configure the settings of the Anti-passback zone and add devices to the zone by clicking Add Device.

·  APB Type

§  Soft - A user who has broken the Anti-passback rule can enter the area without the administrator explicitly releasing the alarm.

§  Hard– A user who has broken the Anti-passback rule can't enter the area without the administrator explicitly releasing the alarm.

·  In case of Disconnected

§  Door Open– Doors in the zone will get opened when the communication between the master and member devices is disconnected.

§  Door Close – Doors in the zone will get closed when the communication between the master and member devices is disconnected.

4. Choose the devices you want to add to the zone as In Device and click the right arrow button. Perform the same for Out Device.

5. Click Apply to transfer the settings to the devices.

Tukang Ngeblog | November 01, 2015 | Access Control, anti-passback, apb, Biomatric Access Control, Card reader, EM Lock, RFID

Read More >>

Site Surveys Planning for Your Customer

Site Surveys – Planning for Your Customer

Most of us have heard the old saying “Prior planning prevents poor performance” and nowhere is it more important than planning out a Video Surveillance System & Access Control System. Taking time upfront to make sure your survey is complete and accurate will save great amounts of time, money and energy for your installers, making both you and the customers bottom line better.

Making the sale and picking the right product are only parts of the puzzle. Camera placement, lens selection, mounting options and cable planning are all equally important to the success of a job. These elements will also help you gain the loyalty of your customer. If you’re a salesman, project manager or an estimator, at some point you’re going to have to put a project together and it will help if you know what to look for.

Of all the various parts of a CCTV system & Access Control System, the one thing the customer is going to notice above all else is a picture that doesn’t meet his expectations. He won’t care what kind of cable you used to get the picture in front of his eyes, nor will he worry about whether there’s a space in between each piece of equipment mounted in a rack. But he will know right away if he can’t see what he thought he was going to see or if what he can see is out of focus.

Picking camera and lens combinations are one of those areas that have become far easier over time. More sensitive cameras and varifocal lenses have taken most of the work out of the selection process. EM Lock installation has taken most of the work out of the selection process. It is still important however to have a good grasp of the concepts.

Focal length of a lens refers to two main things, the distance a lens can see clearly and the width of the scene a particular lens can see. Focal length is rated in millimeters. The lower the millimeter number, the wider the scene. As you go higher in millimeters, the lens becomes more telephoto and the scene width is greatly reduced. Taking the time to pick the right camera and lens combination will make for a smoother install and a happier customer and reduce the need for return visits.

One aspect of a site survey and system design that is frequently over looked is the environment itself. Not only conditions like temperature and weather extremes, but also physical aspects of the environment. I was recently out at a customer’s site looking at a parking lot through the view of his cameras. The customer told me the view was good now but in the spring when the trees bloom he cannot see anything. His system was installed in the winter when all the trees were bare. Please remember that trees grow. Those newly planted saplings will become towering oaks in a few years. Make sure they won’t impede your view now or ever.

Physical obstruction aren’t only limited to the great outdoors. Warehouses are notorious for large shelving and stacks of product. Shelves and products are subject to reconfiguration at any time. Make sure your camera placement is high enough so that it doesn’t get blocked by a stack of boxes.

It seems obvious to take things like that into consideration but I can tell you it doesn’t always happen that way. In times like we are experiencing today the need to get in and out of a project quickly becomes very important to the bottom line, but we can’t let it compromise the integrity of our system design.

Tukang Ngeblog | November 15, 2014 | Access Control, Card reader, Controller, DVR, EM Lock, Focal length is rated in millimeters, Live View CCTV, NVR, Site Surveys for CCTV

Read More >>